|
Gardner Denver 500 S with everything,
ready to drill and for sale now!
|
DRAW WORKS:
GARDNER DENVER 500 S SINGLE DRUM DRAWORKS (S/N 425). 1 1 /8"
LEBIS GROOVED DRUM RATED AT 650 H.P. COMPLETE WITH AIR
CONTROLS, PARMAC
V-80 HYDROMATIC BRAKE (S/N 853). TWO ENGINE COMPOUND POWERED
BY
D-3406B DITA CATERPILLAR 425 GHP. INDUSTRIAL POWER UNITS
(S/N 6TB08724 &
6TB08725) COUPLED WITH CLT-750 ALLISON AUTOMATIC 5-SPEED
POWER SHIFTED TRANS. (S/N2510047240 & 2510060319) DIRECT
DRIVEN INTO G.D. COMPOUND WITH DRIVE SHAFTS.
MAST:
DRECO 131' CANTILEVER MAST (S/NDHW-626) 550,000 L.B. GNC &
385,000 STATIC HOOK LOAD, PIN TYPE WITH 10 LINE CROWN ASSM.,
5 SHEAVE WITH FAST LINE
SHEAVE, GROOVED F/1 1/8" LINE, RACKING BOARD, TONG LINE
COUNTER WEIGHTS, STAND PIPE AND BROOM POLE.
SUBSTRUCTURE:
K&L FAB 12' H X 22' W X 55' L BOX TYPE SUB STRUCTURE WITH
V-DOOR RAMP, (S/N DHW-1191) 400 BBL WATER TANK INCORPORATED
AND STORAGE ROOM,
2" X 3" CENTRIFUGAL PUMP P/B NEW DLC 15 H.P. ELECTRIC MOTOR
(S/N MST29267
76B10HP). COMPLETE WITH (4) SETS OF STEP-UP STAIRS TO RIG
FLOOR, SAFETY
HAND RAILS, BOP STORAGE, JUNK BIN AND NATIONAL TYPE D WIRE
LINE ANCHOR (S/N 124572)
MATTING BOARDS:
SUB BASE MATTING BOARDS (6)
(4- 7'W X 14'L X 6"H)
(1- 8'W X 17' 2"L X 6"H)
(1- 8'W X 31' 8"L X 6"H)
ROTARY TABLE:
RIG COMPONENTS RC-205 (NATIONAL) 20.5" X 53.25" WITH MASTER
BUSHINGS
(S/N 30051222A)
DRILL LINE:
DRILLING LINE SPOOL
BLOCK/HOOK:
SOWA 5-60" SHEAVES, 250 TON CAPACITY, BLOCK HOOK COMBO (S/N
784)
SWIVEL:
COOPER CS-200 TON SWIVEL WITH QUICK CHANGE UNIT (S/N 108)
ELEVATOR LINKS:
2 3/4" X 132 , 250 TON CAPACITY
MUD PUMPS:
(1) F-1000 HENAN ZYZJ 6 3/4" X 10" 1000 HP TRIPLEX MUD PUMP
(S/N 2008-02)
(2) T-1000 IDECO 7" X 10" 1000 H.P. TRIPLEX MUD PUMP (S/N
423), BOTH POWERED BY A D-3508B DITA CATERPILLAR 930 H.P. @
1200 R.P.M. EUI INDUSTRIAL POWER
UNIT (S/N CBB00420) COUPLED WITH A NEW 28" PNUGRIP AIR
CLUTCH AND DUAL
PEDESTAL PUMP DRIVE ASSM. WITH PILLOW BLOCK BEARINGS AND
DRIVE SHAFT WITH PUMP SHEAVE. 6 X 8 BAKER MUD HOG
CENTRIFUGAL CHARGING
PUMP AND 1 X 1 LINER WASH PUMP BELT DRIVEN OFF PINION SHAFT
WITH BELT
GUARDS (S/N 999881BGO & S/N 100963)
UTILITY HOUSE:
10'W X 25'L GENERATOR HOUSE COMPLETE WITH (2) D-3406C DITA
CATERPILLAR
INDUSTRIAL POWER UNIT (S/N 1LS1411 & 1LS0635) COUPLED WITH
NEW 325 KW
NEWAGE-STANFORD , BRUSHLESS, SYNCHRONOUS AC GENERATORS, KW
325
HERTZ 60, RPM 1800, VOLTS 240/480, PHASE 3 (S/N
M06H114742-01 & M06F000763-03)
QUINCY 15 H.P. 125 PSI AIR COMPRESSOR, CURTIS ROCKY SCREW
TYPE AIR COMPRESSOR 30 HP TANK MOUNTED 125 PSI 460 VOLT.
TOP DRILLERS DOGHOUSE:
8'W X 30' TOP DRILLERS DOG HOUSE WITH KNOWLEDGE BOX BENCH,
STORAGE BINS & SHELVES, CREW LOCKERS (2) SLIDING WALK
THROUGH DOORS AND (7)
WINDOWS (SLIDE OPEN SCREENS)
BOTTOM CHANGE DOGHOUSE:
8'W X 30'L BOTTOM CHANGE / PARTS HOUSE WITH (16) LOCKERS,
STORAGE BINS, (1) SLIDING WALK-IN DOOR AND (6) WINDOWS
(SLIDE OPEN SCREENS). ADJUSTABLE RACK FOR TOP DOG HOUSE TO
SIT IN.
MUD HOUSE:
8'W X 12'L MUD MIXING HOUSE WITH MUD HOPPER AND BEAM STAND.
7' HIGH WITH 6' SLIDING DOOR AND WALK IN DOOR.
CATWALK:
5'W X 45'L X 42"H STEEL PLATED
PIPE TUBS:
8'W X 35'L X 42"H PIPE TUBS (5)
JUNK BINS:
8'W X 35'L X 42"H (1)
PIPE RACKS:
(3) SETS OF 42"H PIPE RACKS
CLOSING UNIT
ELECTRIC OVER HYDRAULIC PAYNE 600-F5 STATION REMOTE CLOSING
UNIT COMPLETE WITH CONTROLS & (4) 20 GAL. BOTTLES 2,000 PSI
(S/N 1853)
B.O.P
CAMERON SS 11" 3,000 # DOUBLE RAM BLOWOUT PREVENTOR WITH SET
OF BLIND RAMS & 4 ˝" PIPE RAMS.
LUBESTER:
5 COMPARTMENT, MOTOR OIL, CHAIN OIL, TRANS. FLUID, BOP
FLUID, MOUNTED
ON A 12' X 4'W X 6'H OILFIELD MASTER SKID WITH LOADING
HITCHES.
TOOLPUSHERS HOUSE:
10'W X 9'H X 40'L, SKID MOUNTED WITH APPLIANCES &
FURNITURE.(S/N821040027)
MUD PIT #1:
11'W X 45'L X 6'H, CRIMPED WALL-SLOPED BOTTOMS 3 PARTITION
440 BBL SHAKER MUD PIT WITH DUMP GATES, RUN AROUNDS, DOUBLE
LIFT NEW LINEAR
MOTION SHAKER (S/N3405) W/ GRATED TOP & HAND RAILS, STEPS
(S/NRBT-108R2)
MUD PIT #2:
11'W X 45'L X 6'H CRIMPED WALL-SLOPED BOTTOMS 1 PARTITION
220 BBL SUCTION MUD PIT WITH 110 BBL PREMIX, (S/NRBT-109R2)
W/ 2 ELECTRIC AGITATORS, 2 50 H.P. CENTRIFUGE MIXERS, GRATED
TOP & HAND RAILS,
STEPS (2)
AIR TANK:
250 GALLON 200 PSI MANCHESTER AIR VOLUME TANK MOUNTED INSIDE
OF SUBSTRUCTURE (S/N314885)
AIR HOIST:
HK-12 GARDNER-DENVER AIR TUGGER WITH LONG DRUM (S/NMK-22)
KELLY:
4 ˝ SQUARE KELLY W/ DRIVE BUSHINGS
FUEL TANK:
15,000 GAL. DIESEL FUEL TANK, SKID MOUNTED
WATER TANK:
7'10" X 30'L X 9 ˝"H SKID MOUNTED (500BBLS)
MISC. :
(1) SET REBUILT WOOLEY 4 ˝" 250T DRILL PIPE ELEVATORS
(1) MANIFOLD
(1) SEALTITE WEIGHT INDICATOR
(1) PILOT II AUTOMATIC DRILLER
(1) TONG TORQUE ASSEMBLY
(1) A-1 DEVIATION TOOL
(2) TYPE D 0-5000 MUD GUAGES
(1) STRAIN GAUGE FOR DRILLER WEIGHT
(1) 3 PEN DRILLING RECORDER
(1) CROWN VALVE SYSTEM
(1) 15,000' 15 H.P. RETRIEVER WIRELINE UNIT
(1) SET OF TONGS WITH 3 ˝ - 10 3/4 LATCH JAW SETS
HANDLING TOOLS:
(1) UPPER KELLY VALVE 6 5/8 REG LEFT HAND BOX X 6 5/8 REG
LEFT HAND PIN
(1) 4 ˝ IF LOWER KELLY VALVE
(1) 4 ˝ X HOLE LOWER KELLY BVALVE
(1) SWIVEL SUB WITH 5 ˝ REG L.H. PIN AND 6 5/8 L.H. PIN
(1) 8" BIT SUB W/ 6 5/8 REG BOX X 4 ˝ X HOLE BOX
(1) 4 ˝ REG L.H. BY 6 5/8 REG L.H. PIN TO PIN SWIVEL
(1) BIT SUB WITH 4 ˝ REG BOX & 4 ˝ X HOLE BOX 42"
(1) BIT SUB W/ 6 5/8 REG BOX BOTH ENDS
(1) KELLY SAVER SUB W/ 4 ˝ IF BOX & 4 ˝ HOLE PIN W/ RUBBER
GROOVE
HANDLING TOOLS CONT.:
(1) 4 ˝ X HOLE HANDLING SUB WITH 4 ˝" NECK
(1) “RETRIEVER” WIRELINE UNIT COMPLETE WITH 15 H.P.
(1) LOT HANDLING TOOLS, IE: ROTARY TONGS, DRILL PIPE
ELEVATORS, ROTARY SLIPS, BALES, ETC.
|
